#Serial communication protocol example serial

#Serial communication protocol example serial

Then the USB (Type-B) port of USB-TTL Serial adapter and the USB (Type A) port of the Raspberry Pi is hooked up together. The first option is to connect the TX and RX pins of the DragonBoard to the TX and RX pins on the header of the USB-TTL Serial Adapter respectively. There are two options of using the USB-TTL Serial Adapter for the communication between DragonBoard and Raspberry Pi.

In addition, this module allows a baud rate of 1 Mbps can be reached on the Serial communication. Using this module enables a UART hardware interface available on a USB port. In fact, this module integrates a popular FT232RL chip which is a USB to serial UART interface. To solve those problems, a USB to TTL Serial Adapter module might be a solution. However, new generation computers do not have built-in UART hardware on the mainboard. To enable the computer to communicate with the DragonBoard 410c or Raspberry Pi, UART hardware must also be supported on the computer. However, personal testing showed that the direct connection between the DragonBoard 410c and Raspberry Pi (2/3) is unstable because the DragonBoard 410c is designed to operate at low logic level (1.8V). Technically, DragonBoard 410c and Raspberry Pi 3 can directly communicate with each other via their UART hardware. Moreover, the distance and the data transfer rate are limited. However, the disadvantage is this hardware interface only allows two devices to communicate with one another. The UART (universal asynchronous receiver/transmitter) interface is the hardware that implements this Serial communication. In a simple connection, the RX pin (Receiver) on one side is connected to the TX pin (Transmitter) on the other side. It is a wire-based communication that allows a direct connection between two devices.

Serial communication using the RS-232 protocol is one of the common communication methods. Serial communication using RS-232 Protocol An algorithm is designed to filter the received NMEA messages and extract selected information such as GPS Latitude, Longitude and UTC Time. Basically, the Ublox GPS Module transmits NMEA messages carrying GPS satellite information via Serial communication to the DragonBoard/ Raspberry Pi. A LabVIEW application in the computer will receive these data packages and extract the temperature and humidity measurements.Д®XAMPLE 4 introduces an application of using DragonBoard/ Raspberry Pi to get updated GPS information (Global Positioning System) from a Ublox Neo-M8N GPS Module. The DragonBoard requests measurements of temperature and humidity from the SHT21 sensor, packs these measurement data into data packages and then sends them to the computer. Interrupt technique is also applied between the DragonBoard and Arduino to enhance the coordination.Д®XAMPLE 3 demonstrates application of using Serial communication in transferring data between an IoT device and a computer. The Arduino will process the commands and control the servo motors.

The DragonBoard directs the movement of the Pan and Tilt mechanism by sending the control commands to the Arduino via Serial communication. In addition, a Producer / Consumer pattern is applied for the sending and receiving data.Д®XAMPLE 2 demonstrates a collaboration of DragonBoard (or Raspberry Pi) and Arduino (Nano or Due) to control a 2-DOF Pan and Tilt mechanism using servo motors. Upon receiving the message, the Raspberry Pi will unpack the data and extract the measurements of the sensors. By using the interrupt technique, the Raspberry Pi can take initiative in receiving messages, thereby saving its CPU time instead of using polling technique to wait for the incoming messages. Before sending the data to the Raspberry Pi, the DragonBoard generates an interrupt signal to notify to the Raspberry Pi about its incoming messages. The DragonBoard requests measurements from the MPU-9255 and LIDAR Lite v2 sensors and packs the sensor measurements into data packages. (The examples are broken down into their own links for easy access)Д®XAMPLE 1 demonstrates application of using Serial communication for exchanging data between DragonBoard and Raspberry Pi. In this work, Serial communication (RS-232 protocol) is chosen to demonstrate its application through the following examples. Depending on the communication requirements of the application such as wired / wireless, short distances / long distances, data transfer rates, security etc., suitable communication methods can be selected. It allows devices in a system to communicate with each other in order to exchange information or coordinate to perform some tasks. Communication plays an important role in distributed applications.